|
Description: The new MKII version of the Dynavector DV 507 tonearm has made its long-awaited debut, building on the strengths of the original DV 507 which has enjoyed the highest reputation among audiophiles world-wide since its appearance in 1984. As it is a bi-axis inertia controlled tonearm the DV 507, no matter the type of cartridge can trace the music signal grooves cut in the recording with extreme accuracy. The DV 507 also provides superb trackability on warped recordings. Resolution and musical detailing are quite remarkable. Advantages of Bi-Axis Inertia Controlled Dynamic Balance Type Tonearm: A tone arm is required to operate in two important ways so as to ensure that the cartridge can reproduce faithfully the signal from the record groove. First, there is the need to support the cartridge so that the transfer of the cantilever motion accurately mirrors the audio signal. Secondly, it must maintain an excellent tracking ability for warped records since few records are perfectly flat. These requirements can conflict with each other. However, the bi-axis tonearm provides an effective solution to the problem. Main Features: -Electro Magnetic Damping System for accurate tracking Arm Lift provided The DV507MKII has important sonic improvements as well as being easier to install and use. It includes all of the technology of our tonearm design developed since the DV505 and 501. Bi-axis inertia separation for accurate signal reproduction and superb tracking ability: "Bi-axis inertia separation" may sound complex but it simply refers to a tone arm having two arms which operate independently in the horizontal and vertical planes. In contrast, a conventional tonearm has only one arm which moves both horizontally and vertically. This is called a gimbal type tonearm and the inertia for both planes is the same. The DV507 bi-axis tone arm has a large inertia for horizontal movement and a very small inertia for vertical movement. We shall now explain the reasons why this is advantageous. It is well known that a cartridge generates an audio signal by the differential motion between the cantilever and the cartridge body. Consequently, if the supporting point of the cartridge (the tonearm) vibrates, the tonearm motion affects the audio signal. In these conditions, the signal, which causes the tonearm to vibrate is of low frequency and large amplitude. In the currently used 45-45 stereo record cutting procedure, low frequency signals are almost entirely recorded in a horizontal direction. This means that the low frequency signal, which can cause vibration in the tone arm, exists only as a horizontal force. The tonearm therefore must have sufficient effective mass and rigidity in the horizontal plane in order to provide a stable platform for the cartridge. On the other hand, for the mid to high frequencies, the effective mass of the tonearm should not be too large since the combined mass of the cartridge and the head shell need to be taken into account as well. In particular, where records have a warped surface, the vertical effective mass needs to be small enough to ensure a good tracking ability on such surfaces. To summarise, the tone arm should have a large effective mass and enough damping in the horizontal plane and at the same time a small effective mass in the vertical plane. These conditions are almost impossible to achieve with a tone arm of conventional design using a simple gimbal pivoting system. To solve the problem, Dynavector designed a bi-axis, inertia controlled tonearm where the shorter and lightweight vertical sub arm is placed at the end of the horizontal main arm. This is the special feature of our design. To illustrate how the system works in practice, the following measurements will be of interest:
Cartridge behaviour with two different two different types of tone arm was analysed when tracing warped discs. Fig. 1 is with a conventional tone arm and Fig. 2 with the DV507. In these figures line A refers to the displacement of the record surface and line B the behaviour of the cartridge body. With a conventional tonearm, the displacement of the cartridge is much larger than the actual warp on the disc. At times the cantilever does not touch the record surface. However, the DV507 shows a much better tracking ability because of its low vertical inertia. A non-contact, electro-magnetic damping mechanism has been been
designed to prevent sound distortion and poor tracking performance
arising from arm resonances induced by low frequencies. In this system, a curved rod attached to the rear of the arm is mounted in a magnetic field supplied by two powerful neodymium magnets. Any minute movement of the rod, due to an undamped arm resonance, causes an eddy current to be induced in the rod, which in turn interacts with the magnetic field to return the system to its rest state. As already demonstrated in our DV505 and DV501 arms, this damping system is highly reliable as there is no performance loss with extended use. Expensive Neodymium magnets are employed because of their superior properties and the thicker copper damping plate used gives a much better damping action. Specifications: |
| Home
Theater / Audio & Video |
Pictures are property of Audio Alternative |
©2002-2009
Audio Alternative Inc.. |
|
Audio Alternative
is Atlanta's Premiere Home Theater & Custom Audio Video Design
Center |